LTIBLOX is a consumer to pro interface. It takes a stereo input from consumer grade equipment with a 3.5mm jack (laptop computers, MP3 players, smart phones), sums it to mono then converts it to a mic level balanced XLR output. A built-in volume control adjusts the level of the outgoing balanced signal. 3.5mm male input and XLR male output. Everybody needs one of these!

Features

• Self-contained unit converts input from consumer grade equipment to a mic level balanced output

• Operator volume control of outgoing stereo signal

• 3.5mm male input and XLR male output

• Perfect size for your toolbox or even a shirt pocket

• Black powdercoated aluminum chassis

• Hand soldered connectors

Specifications

Approximate size: 3 1/2" x 1 1/4" x 1"
Some BLOX may be slightly larger due to LEDs, switches, knobs, etc.
The following is a list of connectors on this item:


(1) XLR
(1) 3.5
(1) Potentiometer
(1) DBT
Male panel mount connector
Male wired on 2 ft tail
Volume control with knob
Transformer

TDIBLOX is a consumer to pro interface. It takes a stereo input from consumer grade equipment with a dual RCA connectors (CD or DVD players, tape decks, cable boxes), sums it to mono then converts it to a mic level balanced XLR output. A built-in volume control adjusts the level of the outgoing balanced signal. Dual RCA male inputsand XLR male output. Everybody needs one of these!

CVPBLOX is a continuously variable inline XLR pad with mute (just pull knob up). Housed in a compact metal enclosure with XLR in and out. Very handy!

DBBLOX converts high impedance source to low impedance load. Features 1/4 inch input and XLR male output. Essentially it's a very simple direct box.

DBBLOXF converts low impedance balanced source to high impedance load. Features XLR female input and 1/4 female output. Essentially it's a direct box in reverse.

NEW LOWER PRICE!!!

The Fastset® Musicians/DJ Utility Table is an extremely stable, multi-purpose collapsible table specifically designed for mobile DJs and Musicians on the move. Hands down - it has the fastest setup and tear down time of any table on the market. With our multi-patent technology setup literally only takes a few seconds while changing height settings and tear down is just as quick. This professional table measures 42 inches wide by 18 inches deep, and is less than 2.5” tall when folded flat! It weighs only 20 pounds yet it can support up to a 150 pound load! With 4 adjustable height settings and a sensible footprint, this table is as versatile in the tightest of studios as it is on the road.

This adaptor is designed to supply power where and when you need it. With selectable DC output up to 12 V and plugs to fit most small electronic devices, it replaces a box full of batteries and wall warts.

Features include:
• Auto-detection of AC input from 100 to 240 V for global use
• Selectable DC output for 3, 4.5, 6, 7.5, 9, or 12 V operation
• Six interchangeable plugs to fit most small electronic devices
• A green LED to indicate power on and proper operation
• Short Circuit Protection (SCP) to protect the device
• A folding AC plug for safe and secure storage and transport

Instructions
1. Determine the voltage required to power the device and select the same voltage on the adaptor
2. Locate the DC input on the device (sometimes labeled DC IN) and select the plug that best fits the jack
3. Determine the polarity required to power the device and insert the plug into the cable receptacle to match the polarity
4. Connect the adaptor to line power and operate the device according to the manufacturer's instructions

Precautions:

! Take care to select the proper polarity when inserting the plug into the cable receptacle; failure to do so may damage the device
! Unplug the adaptor before selecting a new DC output voltage; failure to do so may damage the device
! The adaptor emits heat when operating at its maximum capacity for an extended period of time; handle with care when hot
! Disconnect the device immediately when the SCP deactivates the adaptor (the LED dims) to prevent damage to the device

Conforms to ANSI/UL 60950-1
Certified to CAN/CSA C22.2 No. 60950-1

The CBT-500 Cable Tester by Hosa Technology diagnoses signal failure in cables terminated with any combination of XLR, Phone, Phono, and speakON® connectors, as well as DIN, Ethernet, 75-ohm BNC, and USB Type A to Type B cables. It is also equipped with removable leads to verify continuity of additional connectors and jacks. Operation requires one 9-volt battery (included).

Cable Test:
• Turn knob to position 1
• Plug one connector into corresponding jack on left side of tester
• Plug other connector into corresponding jack on right side of tester
• Turn knob to each position to check wiring of each contact

Continuity Test:
• Apply the tip of each lead to the corresponding contacts
• If continuity exists, the center LED will illuminate and tester will beep

Battery Check:
• Turn knob to Battery Check
• LED will illuminate if the battery is charged

The PLUGLOCK-PFP circuit-breaker protected locking outlet strip provides enough wall wart spacing for five bulky transformers and can be safely mounted out of sight, in the rear of your rack.
Secure clamping design "locks" your transformers and conventional plugs in place, ensuring you never get disconnected from your power source. Adjustable clamps accommodate transformers and plugs from 0.4" to 2.1" above outlet.
The sturdy, all steel construction and heavy-duty 5 foot (14 AWG) three conductor cord provide ultimate durability and longevity.

Wall Wart Spacing for Bulky Transformers
Clamps Securely Lock Wall Warts in Place
Clamps Secure Regular Plugs As Well
Mounts Safely Out of Sight in Rear of Rack
Heavy Duty 5 Foot, 14 AWG Cord
Circuit-breaker Protected
Rated 12 Amps
All Steel Construction

Noise Filtration
AC noise filtering to reduce radio frequency and electromagnetic interference (RFI/EMI)
Surge Protection
Spike & surge protection ensures equipment stays safe and your power stays clean
9 Total Outlets
8 rear panel outlets and 1 front panel convenience outlet
Digital Voltmeter
Digital voltmeter display incoming line voltage
15 Amp Rating
15 amp rating, with circuit breaker
"Protection OK" Indicator
Front panel indicator LED lets you know that your equipment is being protected
Wall Wart Spacing Indicator
Rear outlets have been spaced to accomodate even the bulkiest of wall warts and adapters
Front Panel Pull-out Lights
Two retractable incandescent light fixtures with dimmer control for convenient rack illumination

Specifications:
Maximum Output Current: 15 amps
Line Cord: 6 ft., captive, 14 AWG, with 3-conductor Edison plug
Lamps: Two 120V incandescent bulbs, 4 watts each
Operating Voltage: 120VAC 60Hz
Spike Protection Mode: Line to neutral
Energy Dissipation: 170 joules
Peak Impulse Current: 12,000 amps
Maximum Continuous Operating Voltage: 130 VAC RMS
Let Through Voltage (@ 125 amps, 8/20uS waveform) 400 volts
Noise Attenuation: Transverse mode: Greater than 26dB, 200Khz to 10 Mhz
Dimensions: 1.75” H x 19” W x 7.5” D
Weight: 5.8 lbs.
Safety Agency Listing: cTUVus
Warranty: Merit Series units are protected by a limited three year warranty covering defects in materials and workmanship.